Routing and Switching MCQs with Answers
Practice important Routing and Switching MCQs with answers and explanations.
Chapter: 116
Q1381:
What command is used to link a standard ACL to an interface?
A. ip access-group
B. ip access-list
C. access-group
D. acl-link
Correct Answer:
A
Chapter: 116
Q1382:
How do you create a named standard ACL?
A. Use the access-list command
B. Use the ip access-list standard command
C. Use the ip access-group command
D. Use the access-group command
Correct Answer:
B
Chapter: 116
Q1383:
What is the purpose of using the remark keyword in ACLs?
A. To remove an ACL
B. To add comments about ACL entries
C. To apply the ACL to an interface
D. To define ACL number
Correct Answer:
B
Chapter: 116
Q1384:
What should you do to include a comment in an ACL entry?
A. Use the remark keyword
B. Use the comment keyword
C. Use the note keyword
D. Use the description keyword
Correct Answer:
A
Chapter: 116
Q1385:
Which command is used to remove a named ACL?
A. no access-list
B. no ip access-group
C. no ip access-list
D. no acl
Correct Answer:
C
Chapter: 116
Q1386:
To apply a standard named ACL to an interface, which command should be used?
A. ip access-list { access-list-name }
B. ip access-group { access-list-name } in
C. ip access-group { access-list-name }
D. ip acl { access-list-name }
Correct Answer:
B
Chapter: 116
Q1387:
How do you apply a standard ACL to an interface for inbound traffic?
A. Use ip access-group { access-list-number } in
B. Use ip access-group { access-list-number } out
C. Use ip acl { access-list-number } in
D. Use ip access-group in { access-list-number }
Correct Answer:
A
Chapter: 116
Q1388:
What is the maximum length of a remark line in an ACL?
A. 50 characters
B. 100 characters
C. 150 characters
D. 200 characters
Correct Answer:
B
Chapter: 116
Q1389:
To remove a remark from an ACL, which command is used?
A. no access-list remark
B. no ip access-group remark
C. no access-list access-list-number remark
D. no ip access-list remark
Correct Answer:
C
Chapter: 117
Q1390:
What is the first step in planning an ACL implementation?
A. Configure the ACL
B. Verify the ACL
C. Plan the ACL implementation
D. Apply the ACL
Correct Answer:
C
Chapter: 117
Q1391:
How do you apply a standard ACL to an interface?
A. Use the ip access-group command
B. Use the access-list command
C. Use the ip acl command
D. Use the config acl command
Correct Answer:
A
Chapter: 117
Q1392:
What command is used to verify a standard ACL configuration?
A. show access-list
B. show ip access-group
C. show ip acl
D. show acl
Correct Answer:
A
Chapter: 117
Q1393:
What must you do to remove a standard ACL from an interface?
A. Enter no ip access-group command on the interface
B. Enter no access-list command globally
C. Enter remove access-group command on the interface
D. Enter clear acl command globally
Correct Answer:
A
Chapter: 117
Q1394:
Which command is used to configure a standard ACL in global configuration mode?
A. access-list
B. ip access-list
C. ip access-group
D. acl
Correct Answer:
A
Chapter: 117
Q1395:
When planning an ACL implementation, what is essential to determine?
A. The type of ACL
B. The number of ACLs required
C. The interface to which the ACL will be applied
D. The exact configuration commands
Correct Answer:
C
Chapter: 117
Q1396:
What is the main purpose of verifying a standard ACL after configuration?
A. To ensure the ACL was correctly applied
B. To remove old ACL configurations
C. To check if the ACL needs updating
D. To test ACL performance
Correct Answer:
A
Chapter: 117
Q1397:
To configure a standard ACL, what must you enter after the access-list command?
A. ACL number
B. ACL name
C. Interface number
D. Protocol type
Correct Answer:
A
Chapter: 117
Q1398:
What should you do if you want to apply a standard ACL named NO_FTP to an interface?
A. Use ip access-group NO_FTP in
B. Use ip access-list NO_FTP
C. Use access-list NO_FTP
D. Use apply access-group NO_FTP
Correct Answer:
A
Chapter: 117
Q1399:
What is the purpose of the access-list command in standard ACL configuration?
A. To define the ACL
B. To apply the ACL to an interface
C. To verify the ACL configuration
D. To remove the ACL
Correct Answer:
A
Chapter: 118
Q1400:
What command is used to display the current ACL configuration?
A. show access-lists
B. show ip interface
C. show running-config
D. show acl
Correct Answer:
C